Walnut tree is a timber, characterized by significant color diversity. Its color can vary from greyish-black, through a palette of intense brown hues, even to light beige. Walnut timber creates unique and individual floors, which highlight the beauty of both, rustic and modern interiors.

top

top

Allwood Imports located in Portland Oregon was established in 1999. We wholesale hardwood flooring and other home decor wood products through our distributors in North America and Canada. Allwood Floors are exotic real wood floors, with wood species from China, Indonesia, South America and Africa. Our manufacturing base is in China, equipped with the most advanced manufacturing facility and management team. Allwood Floors are gaining popularity for their consistent quality, excellent service and competitive prices.

top

Antiqua is a distressed line of hardwood flooring that exudes beauty and hand crafted design. Each board is individually hand scraped by master artisans to impart the most character of any hardwood floor. Combining the natural character of wood and Allwood's various artistic distressing techniques, we are able to offer Antiqua in a number of distinctly beautiful options for you to choose from. The versatile installation methods of our engineered flooring allows you to enjoy hand crafted beauty almost anywhere.

top

Engineered wood floors are real wood floors that are manufactured using three to five layers of different wood veneers. The sub layers can be of the same species, or of different species. The graining of each layer runs in opposite direction, which makes it very stable. This means that the wood will expand and contract less than solid wood flooring during fluctuations in humidity and temperature.

The top layer of engineered wood flooring consists of high-quality wood.
Engineered floors can be nailed or stapled to a wood sub floor, or glued down to a wood sub floor or concrete slab. This makes engineered floors ideal for slab and basement installations, but they can be used in any room in your home.
This type of flooring can be sanded and refinished, but not as many times as solid wood flooring.

top

Allwood Floors 5/8" & 9/16" Floating Floors

For Floating or Glue-Down Installations

Installer/Owner Responsibility
Beautiful hardwood floors are a product of nature and therefore, not perfect. Our wood floors are manufactured in accordance with accepted industry standards, which permit a defect tolerance not to exceed 5%. The defects may
be of a manufacturing or natural type.
• The installer assumes all responsibility for final inspection of product quality. This inspection of all flooring should be done before installation. Carefully examine flooring for color, finish and quality before installing it. If material is not acceptable, do not install it and contact the seller immediately.
• Prior to installation of any hardwood-flooring product, the installer must determine that the job-site environment and the sub-surfaces involved meet or exceed all applicable standards and recommendations of the construction and materials industries. These instructions recommend that the construction and subfloor be dry, stiff and flat. The manufacturer declines any responsibility for job failure resulting from or associated with sub-surface or job-site environment deficiencies.
• Prior to installation, the installer/owner has final inspection responsibility as to grade, manufacture and factory finish. The installer must use reasonable selectivity and hold out or cut off pieces with defects, whatever the cause.
• Use of stain, filler or putty stick for defect correction during installation should be accepted as normal procedure.
• When flooring is ordered, 5% must be added to the actual square footage needed for cutting and grading allowance.
• Should an individual piece be doubtful as to grade, manufacture or factory finish, the installer should not use the piece.
• Use of appropriate products for correcting subfloor voids should be accepted as a normal industry practice.

Tools & Accessories Needed

• Broom
• Tape Measure
• Chalk line & chalk
• Hand saw or jamb saw
• Electric power saw
• Moisture meter (wood, concrete or both)
• Square
• Installation bar
• Tapping Block (floating)
• 3M 2090 Blue Mask Tape
• Acrylic Filler
• Hammer
• Standard Glue Down Adhesives (Determined by the jobsite conditions, subfloor, etc.) and Adhesive Cleaner
Floors
• Finished hardwood flooring cleaner
• Recommended trowel
• Safety glasses
• 8-penny nails
• Wedges
• Tapping Block (glue-down)

Pre-Installation Procedures
Job Site Inspection
• The building should be closed in with all outside doors and windows in place. All concrete, masonry, framing members, drywall, paint and other "wet" work should be thoroughly dry.
• The wall coverings should be in place and the painting completed except for the final coat on the base molding. When possible, delay installation of base molding until flooring installation is complete.
• Exterior grading should be complete with surface drainage directing water away from the building. All gutters and downspouts should be in place.
• Floating floors may be installed on, above or below grade level. Do not install in full bathrooms.
• Basements and crawl spaces must be dry and well ventilated.
• Crawl space must be a minimum of 24" (600 mm) from the ground to underside of joists. A ground cover of 6-8 mil black polyethylene film is essential as a vapor barrier with joints lapped six inches and taped.
The crawl space should have perimeter venting equal to a minimum of 1.5% of the crawl space square footage. These vents should be properly located to foster cross ventilation.
• Subfloor must be checked for moisture content using the appropriate testing method.
• Permanent air conditioning and heating systems should be in place and operational. The installation site should have a consistent room temperature of 60-75° F and humidity of 35-55% for 14 days prior, during and until occupied, to allow for proper acclimation
Storage & Handling
Handle and unload with care. Store in a dry place being sure to provide at least a four-inch air space under cartons, which are stored upon "on-grade" concrete floors. Flooring should not be delivered until the building has been closed in with windows and doors in place and until cement work, plastering and all other "wet" work is completed and dry. Concrete should be at least 60 days old. Floating floors should be stored in the environment in which it is expected to perform. Air conditioning/heating systems should be in place and in operation at least 14 days prior, during and after installation of the flooring. Do not open the packages until you are ready to install.
Humidity may cause the tongue to swell on opened packages making installation difficult. Check adhesive label for storage limitations.

Installation Methods
Floating
• Use floating floor underlayment appropriate for jobsite conditions.
• Use joint adhesive appropriate for jobsite conditions.

Glue-Down Installation
• Use recommended trowel to get required spread rate and ridging height.
• Use joint adhesive appropriate for jobsite conditions.


Subfloor Requirements
Subfloor Guidelines:
• CLEAN - Scrape, broom clean, and smooth. Free of wax, paint, oil, sealers, adhesives, curing agents and other debris.
• LEVEL/FLAT - Within 3/16" in 10' and/or 1/8" in 6'. Sand high areas or joints. If the floor is to be glued down, fill low areas (no more than 1/8" at a time) with a cementitous leveling compound or milk additive latex patch of 3,000-PSI minimum compressive strength. Follow the instructions of the leveling compound manufacturer. Leveling compounds must be tested for moisture to ensure they are properly cured and within the manufacturer's specified requirements for proper installation.

• STRUCTURALLY SOUND - Nail or screw any loose areas that squeak. Replace any water-damaged, swollen or delaminated subflooring or underlayment. Avoid subfloor with excessive vertical movement unless they have been properly stiffened prior to the installation of the wood flooring.
• DRY - Check moisture content of the subfloor with a reliable moisture meter.
Recommended Subfloor Surfaces

• PREFERRED: 3⁄4" (19 mm) CDX grade plywood
3⁄4" (23/32") OSB PS2 rated underlayment
MINIMUM: 5/8" CDX grade plywood
• Existing solid wood flooring
• Vinyl, resilient tile, cork flooring
• Concrete slabs
• 3⁄4" chip, waferboard, particleboard
• Radiant heated subfloors
• Acoustic concrete
• Ceramic, terrazzo, slate and marble
• Metal
• Cork (Acoustic)
Concrete Slabs
Floating floors can be glued directly to concrete or floated over them. In glue-down applications, do not use a concrete sealer nor install over one. Surface preparation using mechanical methods such as sanding or scouring with open coat paper or a titanium disk is preferred. The concrete must be of high compressive strength. All concrete subfloors should be tested for moisture content. Visual checks are not reliable. Acceptable test methods for subfloor moisture content include:
NOTE: Test several areas, especially near exterior walls and walls containing plumbing.
• A 3% Phenolphthalein in Anhydrous alcohol solution. Chip the concrete at least 1⁄4" deep (do not apply directly to the concrete surface) and apply several drops of the solution to the chipped area. If any color change occurs, further testing is required.
• Calcium Chloride test. The maximum moisture transfer must not exceed 3 lbs./1000 square feet with this test.
• Moisture readings should not exceed 4.5 on the upper scale.
A "DRY" SLAB, AS DEFINED BY THESE TESTS CAN BE WET AT OTHER TIMES OF THE YEAR. THESE
TESTS DO NOT GUARANTEE A DRY SLAB. ALL CONCRETE SLABS SHOULD HAVE A MINIMUM OF 6 MIL POLY FILM VAPOR BARRIER BETWEEN THE GROUND AND THE CONCRETE.
Vapor Barrier System: If moisture is present, inexpensive sheet vinyl or "slip-sheet" (PVC) may be installed. Use a premium grade, alkaline resistant adhesive and a full spread application system to properly bond the vinyl to the subfloor. Follow the sheet vinyl manufacturer instructions for installation procedures. A patch test may be required as an adhesion test. Install several small areas (3' x 3') and allow the vinyl to set for 72 hours. Remove the vinyl; if the backing remains attached to the concrete, the subfloor should be acceptable for sheet vinyl installation. If you have any questions regarding installation or the handling of moisture problems, please contact the distributor/retailer from whom the goods were purchased.
Acoustic Concrete
Acoustic concrete normally contains large quantities of gypsum that may inhibit the adhesive's capability to properly bond. For glue-down applications, acoustic concrete must be primed with the concrete manufacturers recommended primer/surface hardener.
Wood Subfloors & Wood Structural Panel Subfloors
Plywood: Must be APA grade rated sheathing or CDX minimum.
Oriented Strand Board (OSB): Must be PS2 rated installed sealed side down.
Particleboard must be a minimum 40-LB density, stamped underlayment grade and 3⁄4" thick.
Make sure existing floor or subfloor is dry and well nailed or screwed down every 6" along each joist to avoid squeaking or popping before the floor is installed. The wood subfloor must not exceed 13% moisture content.
Measure moisture content of both subfloor and wood flooring to determine proper moisture content with a reliable wood moisture meter. The difference between the moisture content of the wood subfloor and the wood flooring must not exceed 4%.
Optimum performance of hardwood floor covering products occurs when there is no horizontal or vertical movement of the subfloor. The MINIMUM subfloor recommendations described above for 16" O/C joist spacing.
The thicker, PREFERRED subfloor recommendations described above will allow 19.2" O/C joist spacing if the joist manufacturer's recommended span is not exceeded. Spacing in excess of 19.2" O/C does not offer optimum results. Install flooring perpendicular to the floor joists when possible. Installations should not be made parallel to the floor joists or on joist spacing that exceeds 19.2" O/C unless the subfloor has been properly stiffened.
Stiffening may require the addition of a second layer of subflooring material to bring the overall thickness to at least 1-1/8".
All underlayment panels should be spaced 1/8" apart to insure adequate expansion space. This can be achieved by using a circular saw set at the depth of the underlayment and cutting around the perimeter of the panel. T&G panels normally have built in expansion; DO NOT cut around the perimeter of T&G panels. Do not install over existing glue-down wood floors. Do not install over nailed floors that exceed 3-1⁄4" in width. Wide width floors must be overlaid with plywood. When installing over existing wood floors parallel with the flooring, it may be necessary to install an additional 1⁄4" layer of plywood to stabilize the flooring or install the wood floor at right angles.
Applicable standards and recommendations of the construction and materials industries must be met or exceeded.
Resilient Tile, Resilient Sheet Vinyl & Cork Flooring
If the tiles or sheet goods are well bonded, the flooring can be glued directly to the surface. Clean the surface thoroughly with a good quality household detergent. De-gloss flooring as necessary to create a good adhesive bond using an abrasive pad. If vinyl appears to have a coating of wax or other maintenance materials, it must be removed with the appropriate floor stripper. Allow ample drying time. (Note: Do not sand any resilient products for they may contain asbestos fibers, which may be harmful.) Do not direct glue to floors that exceed two layers; install as a floating system only under these circumstances. Cork floors must have all sealers and surface treatments removed before installation begins if a direct glue-down application is preferred.
Ceramic, Terrazzo, Slate & Marble
All grout joints and broken corners that exceed 1" must be filled with a cementitous leveling compound mixed with
Latex additive of a glue-down application is preferred. The surface should be cleaned and abraded to create a good bonding surface for the adhesive. Loose tiles must be re-adhered to the subfloor or filled as above for both glue-down and floated applications.
Cork (Acoustic)
Floating floors can be glued or floated directly over full-spread, permanently bonded acoustic cork. The cork should have a density of no less than 11.4 lb./cubic foot and no more than 13 lb./cubic foot. The cork, in general, should be pure cork combined with a polyurethane binder. Cork thickness is to be no more than 1⁄4" (6 mm). Install cork in accordance with manufacturer's recommendations. DO NOT use cushion underlayment when floating over these surfaces.

Subfloors with Radiant Heat
• System must be operational and heated for at least 7 days prior to beginning installation.
• Turn off heat and let subfloor cool down to room temperature 3-4 hours prior to starting the job.
• Radiant heated floors must be temperature controlled or engineered for the R-rating of the floor-covering product installed upon them. BEFORE installation begins, ascertain that the system is designed and controlled for wood flooring. Failure to do so may cause excessive heat damage, shrinkage and
delamination.
• After installation, turn system back on immediately to its normal room temperature setting. The subfloor surface must not exceed 85° F throughout the life of the floor.
Doorway & Wall Preparation
Undercut door casings. Remove any existing base, shoe mold or doorway thresholds. These items can be replaced after installation. All door casings should be notched out or undercut to avoid difficult scribe cuts.

Installation Tips
• Floor should be installed from several cartons at the same time to ensure good color and shade mixture.
• Be attentive to staggering the ends of boards in adjacent rows at least 16" when possible. This will help ensure a more favorable overall appearance of the floor.
• DO install from closed/sealed cartons. DO NOT remove materials from their sealed container prior to installation.
• DO tighten panels by tapping against the recommended tapping block with a hammer. DO NOT tighten panels by striking directly with the tapping block or a hammer.
• DO glue all joints with appropriate sealer for the jobsite conditions when using a floating system. The glue
MUST be applied to the top of the tongue, DO NOT apply adhesive in the groove.
• DO use a starter board that is adequately fastened to a straight starting line.
• DO use Comfort Guard underlayment on all floating floors over subfloors that require it.
• DO NOT use short tapping blocks that can damage the edge. Do Not use lightweight wooden tapping blocks. Do Not use grooved tapping blocks.
• DO NOT use laminate straps to tighten the flooring panels.

STEP 1: Establish a Starting Point
• Installation parallel to the longest wall is recommended for best visual effects, however, the floor should be installed perpendicular to the flooring joists unless subfloor has been reinforced to reduce subfloor sagging. Find appropriate subfloor from "Subfloor Type" section in this instruction manual.
• When possible, always begin layout or installation from an outside wall, as these are normally the straightest.
• Pre-plan the floor by counting the number of planks (in width) that it will take to complete the floor. Avoid finishing out with a rip narrower than 2". Plan to start the first row with a partial board, ripping it to the necessary width to avoid a narrow rip on the final wall.
• In at least two places 12"-16" from the corner, measure out equal distance from the starting wall and snap a chalk line. The chalk should be of a bright color so that it is visible through the underlayment or adhesive. If a partial, ripped board is required (as above) it can be installed after the balance of the flooring has been completed. Adjust the starting line to allow for the width of the board plus 1⁄2" for expansion. Ascertain that the wall is straight. If it is not, scribe the first row to allow for irregularities.
• Install a starter board on the inside edge of the chalk line aligned to create a straight edge to work against. Attach the starter board to the subfloor using nails appropriate to the subflooring materials.
When installing using the floating system install the cushion underlayment BEFORE installing the starter strip.


Floating Floor Installation
STEP 2: Installing the Underlayment
• Roll the underlayment in the same direction that the wood flooring is to be installed.
• Extend the underlayment a few inches up the wall. Excess will be trimmed off prior to installing trim or moldings.
• Firmly bond the sheets together to cover the entire floor. The floating floor underlayment already has double-sided tape for ease of taping the precut overlapping seams.
• Always allow 1⁄2" expansion around all vertical objects.
STEP 3: Installing the Floor
• Select your first board; apply a continuous 1/8" glue bead to the top of the tongue on "the end of the board." Do not apply glue to the side-tongue at this time.
• Lay the first board with the grooves facing the edge of the starter board and the left wall of the room. (Always leave expansion space).
• Complete the first row. Cut the last board allowing for 1⁄2" clearance between the wall and the floor. (Use the remaining end of the cut board as a starter board for any row afterrow three). Use an installation bar to pull the last board into place. Install wedges into the gap and tighten.
• If any glue gets on the surface of the flooring, wipe off immediately with a damp cloth.
• Start the second row by applying a bead of adhesive along the top side of the tongue of row one.
• Cut a board in half for the first board of the second row. Avoid installation of any boards shorter than 25" in the first four rows, which may reduce the strength of the floor.
• In the remaining rows, stagger joints at least 16" apart. When installing boards together, use a tapping block against the tongue, not the groove. Apply a bead of adhesive to the tongue on the end and side.
Tap the boards into place by tapping with a hammer on the tapping block. DO NOT tap directly on the boards with the hammer. Install the rest of the floor. Be sure all joints are tight. Use spacers on the long and butt walls. Use an installation bar to tighten the joints from the ends. Remove excess adhesive with a damp towel.
• The final row of boards, in most installations, will need to be ripped lengthwise to fit. The cut has to compensate for uneven walls and the expansion clearance or gap necessary between the wall and the flooring. First lay up the last row, face-up over the top of the last row permanently installed. Now using a stub of a board and a pencil, scribe the proper guide lines and cut.
• Use an installation bar to pull in the last row and install wedges.
• Remove the starter board and install the final row using the installation bar as above.
• Allow the completed floor to rest undisturbed (no foot traffic) for a minimum of 8 hours before removing the wedges.
• Before leaving the job site, check the floor under proper lighting for any trace of glue on the surface. Use Adhesive Cleaner to remove stubborn glue. Install molding the following day. Refer to the floor care and maintenance section for maintaining your wood flooring.

Glue Down Method
STEP 1: Preparation
• Maximum Adhesive Working Times
• Urethane Adhesive - 60 minutes (Always read container label before proceeding)
• Polymeric Resin Adhesive - 90 minutes (Always read container label before proceeding)
• Open times and curing times of ALL adhesives vary dependant upon subfloor porosity, air movement, humidity and room temperature. Urethane adhesives have a shortened work time in high humidity environments whereas polymeric resin adhesive working time will be lengthened. In areas of low humidity, open time will be longer with urethanes and shorter with polymeric resins. Adjust the amount of adhesive spread accordingly. The adhesive should not be applied if subfloor or room temperature is below 65° F (20° C).
• Spread sufficient amounts of adhesive with the recommended trowel in an area that can be covered in 60-90 minutes. Polymeric resin adhesives should be rolled every two hours and at the end of the day. If a urethane adhesive is to be rolled, do not do so until the adhesive has cured for two hours.
NOTE: Avoid installing from the surface of the flooring. If necessary distribute weight using a kneeler board.
Always refer to specific adhesive instructions on the adhesive label. Comfort Guard underlayment will not be used in this application.

STEP 2: Spreading the Adhesive
• Hold trowel at a minimum 45° angle firmly against the subfloor to obtain a 50-60 sq. ft. per gallon spread rate. The trowel will leave ridges of adhesive and very little adhesive between the ridges. This will allow you to still see the chalk lines between the ridges and provide the recommended spread rate. If the adhesive skins over and fails to transfer, remove and spread new adhesive to achieve proper bonding to the subfloor. WORKING TIME WILL VARY DEPENDING ON JOB SITE CONDITIONS.
• During the installation occasionally remove a piece of flooring from the subfloor and inspect the back for proper adhesive transfer. Adequate adhesive transfer is necessary to ensure sufficient holding strength.
• For additional application instructions, follow the recommendations on the adhesive container.
• When not in use, keep the adhesive container tightly closed to prevent thickening. Thickening will cause difficulty in spreading the adhesive.
• Proper ventilation within the room must be provided. An electric fan is helpful.
• If the floor is to be covered, use a breathable material such as cardboard. Do not cover with plastic.

NOTE: Clean adhesive from the surface of the floor frequently using the recommended adhesive cleaner.
Do not use blue tape before adhesive is removed. Use a clean towel, changed frequently to prevent haze and adhesive residue.

STEP 3: Installation of Flooring
• Use the straightest boards available for the first two rows. The first row of planks should be installed with the edge of the groove lined up against the starter board. The tongue should be facing the starting wall.
The first row must be aligned and seated in the adhesive as all additional rows will be pushed back to this original row.
• Apply a bead of adhesive to all of the end tongues prior to installing into the adhesive. Gluing of the edges is not necessary in glue-down applications.
• Use wedges against the starting wall to prevent movement. Tighten or loosen as necessary to allow for variations in the wall, always keeping planks aligned with the chalk line.
• Avoid working from the surface of the newly installed floor to prevent scooting. Use a kneeler board if necessary to distribute weight.
• When installing planks, engage the end-joint first as close to the side (long) tongue and groove as possible and then slide together tightly to engage side (long) joint tongue and groove. To avoid adhesive bleed-through and memory pull-back, avoid sliding pieces through the adhesive as much as possible when placing them in position.
• Check for a tight fit between all edges and ends of each plank. End-joints of adjacent rows should be staggered 16" when possible to ensure a more favorable overall appearance.
• Use a glue-down tapping block and a hammer to tighten all joints.
• To eliminate minor shifting or gapping of product during installation, use 3M 2090 Blue Mask Tape to hold the planks together. After installation is complete, remove all the 3M 2090 Blue Mask Tape from surface of newly installed flooring. Do not let tape remain on flooring longer than 24 hours. Avoid use of masking tape, which leaves an adhesive residue.
• Be sure not to spread adhesive too far ahead of your work area.
• Complete the installation using this same technique for the remainder of the floor.
• Remove the starter board and install the final row as above.
• Avoid heavy foot traffic on the flooring for at least 24 hours. Lift the furniture or fixtures back into place after 24 hours.


INSTALLERS – Advise Your Customer of the Following
SEASONS: Heating and Non-Heating
Recognizing that wood floor dimensions will be slightly affected by varying levels of humidity within your building, care should be taken to control humidity levels within the 35-55% range. To protect your investment and to assure that your floors provide lasting satisfaction, we have provided our recommendations below.
• Heating Season (Dry) - A humidifier is recommended to prevent excessive shrinkage in wood floors due to low humidity levels. Wood stoves and electric heat tend to create very dry conditions.
• Non-Heating Season (Humid, Wet) - Proper humidity levels can be maintained by use of an air conditioner, dehumidifier, or by turning on your heating system periodically during the summer months.
Avoid excessive exposure to water from tracking during periods of inclement weather. Do not obstruct in any way the expansion joint around the perimeter of your floor.
Floor Repair
Minor damage can be repaired with a Touch-Up Kit or Acrylic Filler. Major damage will require board replacement, which can be done by a professional floor installer.
ALL Installations
STEP 4: Completing the Job
• Clean floor with the appropriate Cleaner. (See adhesive container for specific information)
• Re-install any transition pieces that may be needed, such as Reducer Strips, T-moldings, or Thresholds. The products are available pre-finished to blend with your flooring. (See moldings below)
• Re-install all base and/or quarter round moldings. Nail moldings into the wall, not the floor. Inspect the floor, filling all minor gaps with the appropriate blended filler.
• If the floor is to be covered, use a breathable material such as cardboard. Do not cover with plastic.
• Leave warranty and floor care information with the owner. Advise them of the product name and code number of the flooring they purchased.
• To prevent surface damage avoid rolling heavy appliances and furniture on the floor. Use plywood, hardboard or appliance lifts if necessary.
Moldings
• Reducer Strip: a teardrop shaped molding. Used around fireplaces, doorways, as a room divider, or as a transition between Parquet and adjacent floor coverings that are thinner. Fasten down with adhesive or double-faced tape.
• Threshold: a molding undercut for use against sliding door tracks, fireplaces, carpet, ceramic tile, or existing thresholds to allow for expansion space and to provide a smooth transition in height difference.
Fasten to subfloor with adhesive and/or nails through the heel. Predrill nail holes to prevent splitting.
Always leave expansion beneath the undercut.
• Stair Nosing: a molding undercut for use as a stair landings trim, elevated floor perimeters, and stair steps. Fasten down firmly with adhesive and nails or screws. Predrill nail holes to prevent splitting.
• Quarter Round: a molding used to cover expansion space next to baseboards, case goods, and stair steps. Predrill and nail to the vertical surface, not into the floor.
• Combination Base and Shoe: a molding used when a base is desired. Used to cover expansion space between the floor and the wall. Predrill and nail into the wall, not the floor.
• T-Molding: a molding used as a transition piece from one flooring to another or to gain expansion spaces. Fasten at the heel in the center of the molding. Leave expansion beneath the undercut on both sides.

top

The Warranties described below are given to the original purchaser only AND ARE SUBJECT TO THE PROCEDURES, LIMITATIONS, DISCLAIMER'S AND EXCLUSIONS SET FORTH HEREIN. The Warranties cover only approved product applications as recommended by Allwood Import, LLC Floors and are effective on hardwood flooring products described below purchased after JANUARY 1, 2000
Lifetime Structure Warranty 
Allwood Import, LLC warrants its products, in their original manufactured condition, to be free from defects in lamination, milling and dimension for as long as the original purchaser owns the floor. Hardwood flooring, being a natural product, will continue to expand and contract through heating and non-heating seasons. Properly installed hardwood floors may consequently experience some separation between the boards at different times during the year. If such separation occurs, it is not considered a product defect and is not covered by this warranty.
FULL FINISH WARRANTIES
Allwood Import, LLC warrants to the original purchaser that the finish on Allwood factory finished products, from the date of purchase, when used under normal residential traffic conditions, as applicable, will not wear through or separate from the wood for the period of 25 years, on the engineered wood layers purchased after JANUARY 1, 2000. On commercial applications Allwood Import, LLC warrants to the original purchaser that the finish on Allwood factory finished products, from the date of purchase, when used under normal commercial traffic conditions, as applicable, will not wear through or separate from the wood for the period of 5 years, on the engineered wood layers purchased after JANUARY 1, 2000.
All commercial and residential finish warranties exclude any indentations, scratches or damage caused by lack of proper maintenance, misuse, negligence, spiked heel shoes, pets, insects, water, moisture, erosion, pebbles, sand, other abrasives, insufficient protection on furniture, wet mopping or failure to follow all the manufacturer's written maintenance instructions. Use of floor care products other than those especially formulated for use on hardwood or prefinished flooring, may damage your floor and may void the warranty.
25-Year Finish Warranty 
Allwood Import, LLC warrants to the original purchaser that the finish will not wear through or separate from the wood for the lesser of 25 full years or as long as the original purchaser owns the home for all Allwood Import, LLC flooring.
ALLWOOD IMPORT, LLC Warranty Protection Means; 
If in the unlikely event any portion of your floor should fail with respect to the provisions of these warranties, Allwood Import, LLC, at its sole option, to the original purchaser, will replace such portion, AT NO COST TO YOU, with the same product or another product of equal value. In the unlikely event Allwood Import, LLC is unable to correct the failure, Allwood Import, LLC will refund, if requested, the purchase price for that portion of the floor that fails. To file a claim, first contact the Allwood Import, LLC distributor/dealer where the original purchase was made or contact us at Allwood Import, LLC 12817 NE Airport Way, Portland, Oregon 97230, Attn: Claims Department. Claims must also be filed within the warranty coverage period and information verifying date of purchase will be required. Allwood Import, LLC reserves the right to have a designated Allwood Import, LLC representative inspect the floors and remove samples for technical analysis.
Allwood Import, LLC warranties are not transferable.
No installer, retailer, distributor or agent, or employee of Allwood Import, LLC Hardwood Floors, has the authority to alter the obligations or limitations of any Allwood Import, LLC warranty.
RADIANT FLOOR HEATING

Allwood Import, LLC additionally warrants that all its engineered hardwood flooring products, even when applied on a radiant heated concrete subfloor, with subfloor surface temperature not exceeding 85°F. will not buckle, cup or warp for as long as the original purchaser owns the floor when properly installed according to installation instruction procedures, and when properly maintained in accordance with such instructions. Hardwood flooring, being a natural product, will continue to expand and contract through heating and non-heating seasons. Properly installed hardwood floors may consequently experience some separation between the boards at different times during the year. If such separation occurs. It is not considered a product defect and is not covered by this warranty.
Sources of additional information: 
Sources of additional information regarding installation and maintenance of Allwood Import, LLC hardwood flooring products can be found in the following: Installation sheets, which are included in every carton, and the Allwood Import, LLC Floor Care and Product Warranty Guide. By following all recommended installation and maintenance procedures as specified by Allwood Import, LLC, you will assure yourself the maximum enjoyment of your Allwood Import, LLC hardwood floor.
Warranty disclaimers and exclusions
Color variations in flooring are a natural occurrence due to species, age, character of flooring and exposure to UV light or sunlight. For these reasons, new and/or replacement flooring may not match display samples and/or existing flooring.
Due to color variations of product and/or samples, Allwood Import, LLC is not responsible for the consumer matching flooring to other wood products, such as cabinets, stair railings, trim and moldings.
Gloss reduction is not considered surface wear.
Natural occurring wood characteristics such as variations in grain, color, mineral streaks, and knots, are not considered defects.
Normal exposure to sunlight will bring about changes in the shading of any hardwood floor as the floor ages. Area rugs should be moved occasionally as they block sunlight and may give the appearance of discoloring under the rug. This is not a product defect.
Installations must be performed in accordance with all Allwood Import, LLC installation instructions.
It is the responsibility of the installer and/or the homeowner to inspect boards prior to installation. Allwood Import, LLC accepts no responsibility for costs of product or labor when boards with visible defects have been installed.
Damage due to water and/or moisture including but not limited to damage resulting from broken or leaking pipes, wet mopping, or weather conditions or natural disasters, is excluded from Allwood Import, LLC warranties.
Warranty Exclusions

ALLWOOD IMPORT, LLC WARRANTIES DO NOT COVER INDENTATIONS, SCRATCHES, STAINS OR DAMAGE CAUSED BY NEGLIGENCE, FIRE, WATER, MOISTURE, EXCESSIVE HEAT OR EXCESSIVE DRYNESS, EROSION, PEBBLES, SAND, OR OTHER ABRASIVES, PETS, INSECTS, SPIKED HEEL SHOES, WEATHER CONDITIONS OR NATURAL DISASTERS, COLOR VARIATIONS, NATURALLY OCCURRING WOOD CHARACTERISTICS, FAILURE TO FOLLOW ALL THE MANUFACTURER'S WRITTEN INSTALLATION AND/OR MAINTENANCE INSTRUCTIONS, IMPROPER MAINTENANCE, WET MOPPING, INSUFFICIENT PROTECTION, MISUSE, OR IMPROPER ALTERATIONS OF THE ORIGINAL MANUFACTURED PRODUCT.ALLWOOD IMPORT, LLC WARRANTIES DO NOT COVER NATURAL EXPANSION AND CONTRACTION RESULTING IN SEPARATION BETWEEN BOARDS OR DAMAGE CAUSED BY LOW OR EXCESSIVE HUMIDITY. NO WARRANTIES APPLY TO ANY PRODUCT OR PRODUCTS DESIGNATED AS THRIFT, ANTIQUE, TAVERN, BARGAIN OR CABIN GRADES, SECONDS, ECONOMY GRADE, OR NON-STANDARD ITEMS. ANY PRODUCT OR PRODUCTS SO DESIGNATED ARE SOLD 'AS IS'. THIS WRITING IS THE COMPLETE AND EXCLUSIVE STATEMENT OF THE EXPRESS WARRANTIES PROVIDED HEREIN AND IS IN LIEU OF ALL OTHER EXPRESS AND/OR STATUTORY WARRANTIES BY THE MANUFACTURER, TO THE EXTENT PROVIDED BY LAW. THERE ARE NO IMPLIED WARRANTIES EXTENDING BEYOND THE TERMS OF THIS WARRANTY. ALLWOOD IMPORT, LLC ASSUMES NO LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. HOWEVER, SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE. THE SOLE REMEDY PROVIDED HEREIN IS THE REPAIR, REFINISH OR REPLACEMENT OF DEFECTIVE PRODUCTS, OR REFUND FOR DEFECTIVE PRODUCTS.

top

Adds definition to the boards and helps hide minor irregularities, such as uneven plank heights.

top

top

Maintenance & Care Instructions 

Initial Care: Following Installation, clean NO WAX floor cleaner.

 Routine Care: Frequently sweep or vacuum the floor to remove loose dirt before it can scratch or be ground into the floor's surface. For spot cleaning, apply cleaner onto a clean cloth and rub onto the spot. Never apply a wax topical to your floor.
Periodic Care: Follow sweeping and vacuuming instructions for Routine Care. Spread cleaner directly on the floor and wipe with a sponge mop or appropriate cleaning applicator. DO NOT allow puddles a NO WAX cleaner to remain on floor's surface. Excess liquid may damage the fiber of the wood.
An Ounce of Prevention:
Never clean or wet mop your hardwood floor with water. Do not use any wax or cleaner that must be mixed with water such as oil soap, as this may ruin your floor and result in a loss of warranty. Water can dull the finish and permanently damage the floor.
If your floor abuts exterior doors, put outside doormats at the entrances to keep dirt and moisture from being tracked in. Inside, you may want to add an area rug to further prevent dirt and moisture from being tracked onto your hardwood floor. Don't use rubber, foam back, or plastic mats as they may discolor the floor. To prevent slippage of area rugs, use an approved vinyl rug underlay from a reputable manufacturer.
Area rugs should be moved occasionally as they block sunlight, which may give the appearance of discoloring under the rug.
Use floor protectors on the feet of furniture to avoid scratches. There are several sizes of floor protector pads available. When moving heavy furniture or appliances, use extra caution to help avoid scratching, indentations, and gouging. Some objects may be too heavy to be moved across a hardwood floor under any circumstances.
Certain types of casters on furniture may damage hardwood flooring. Barrel-type caster wheels or wide, flat glides are best for protecting your hardwood floor. If your furniture does not have the right type of caster, we recommend that you change them.
A humidifier is recommended to prevent excessive shrinkage of wood floors due to low humidity levels. Wood stoves and electric heat tend to cause very dry conditions. A humidity level of 35-55% is recommended.
In damp conditions, proper humidity levels can be maintained with an air conditioner or dehumidifier, or by periodically turning on your heating system during the summer months.
Spike or stiletto high-heel shoes, especially those in poor repair, may cause denting and related damage to hardwood floors due to the extremely high compressive force they generate. Such footwear can produce dynamic loads in excess of 1000 pounds per square inch, even when worn by someone of slight or average build. Allwood Import, LLC will not accept claims from damages, which arise from such exposure.
Tips on Repairing Blemishes
Most problems can be prevented or minimized by wiping up any spills immediately. We have provided some common first aid procedures for spot cleaning and touch-up/repair of your floor. When removing a spot, always begin at the outer edge and work towards the center to prevent the spot from spreading. Keep a touch-up kit, which blends with your factory-stained floors available. This kit contains all the materials you will need to handle most of the accidents listed here.

Repair Tips for Prefinished Floors 

Spots caused by food, water or animals: 
Place a NO WAX cleaner on a clean cloth to remove the stain or spot. More stubborn spots may require additional scrubbing with a NO WAX cleaner and a scrub pad.
 Greasy spots or ink spots: 
Rub grease, tar, lipstick, crayon, rubber scuffs, or oil spots with a cloth or scrub pad dampened with a NO WAX cleaner. If stain remains, rub with a cloth or scrub pad dampened with cleaner and follow up by cleaning area with a NO WAX cleaner.
 Cigarette Burns: 
Most common burns can be repaired with a standard touch-up kit. Rub area with fine sandpaper, restain with a stain marker and refinish with urethane. For cigarette burns that extend deep into the surface of the wood, individual plank, strip, or parquet boards may need to be replaced.
 Chewing gum, candle wax: 
Apply a plastic bag filled with ice on top of the deposit until it becomes brittle enough to crumble off. A standard cleaner can be helpful in removing stubborn areas. After deposit has been removed from the surface of the floor, clean entire area with a NO WAX floor cleaner.
 Expansion cracks and squeaks: 
Hardwood floors are affected by two distinct humidity seasons - heating and non-heating. Recognizing that wood floor dimensions will be slightly affected by varying levels of humidity, care should be taken to control humidity levels within the 35-55% range. If humid or damp weather causes a slight expansion in your hardwood floor, the edges of boards may rub together, producing a squeak. For solid oak floors, a liberal amount of talcum powder between the squeaking boards will usually quiet things down. For engineered, glued-down floors with squeaking boards or loose popping sounds, inquire about the standard adhesive repair kit at your local retailer. Avoid excessive exposure to water from tracking during periods of inclement weather; do not obstruct the expansion joints around the perimeter of your floors.
 Refurbishing scratched areas: 
Most scratches can be repaired with the touch-up kit. Since your floors are factory finished, individual planks, strips or parquets that are heavily gouged or damaged can be replaced. If needed, the entire floor can be refurbished by sanding and recoating with an approved urethane. For repairing areas where scratches extend over several boards, tape off repair area at the end of joints and along the outer edge of each plank/strip/parquet surrounding the scratched or worn area with 3M 2090 Blue Mask tape before applying stain/urethane to prevent the stain/urethane from splattering or being transferred to the surrounding undamaged boards.

top